近年來，泡沫復合板的使用普遍，給人們帶來了嚴重的損失。因此，在選擇泡沫復合板時，一定要選擇正規渠道購買，并嚴格按照防火要求建造，選擇泡沫復合板。在此過程中應注意以下幾點：

In recent years, the use of foam composite board is widespread, which has brought serious losses to people. Therefore, when choosing foam composite board, we must choose regular channels to purchase, and build it in strict accordance with the fire prevention requirements, and choose foam composite board. In this process, the following points should be noted:

選用優質的泡沫復合板原材料，從根本上保證泡沫復合板的產品質量。購買高檔泡沫復合板嚴格按照防火要求購買，不要貪便宜不關注泡沫復合板芯材的防火性能和防火等級

Select high-quality foam composite board raw materials to fundamentally ensure the product quality of foam composite board. Purchase high-grade foam composite board in strict accordance with the fire protection requirements. Don't be greedy and don't pay attention to the fire performance and fire rating of foam composite board core materials

在泡沫復合板的交付和安裝過程中，仔細檢查板的質量和平整度，避免因板的質量造成工程安全隱患。通過正規渠道購買泡沫復合板，并向生產廠家索取消防部門出具的產品防火測試報告。

During the delivery and installation of foam composite board, carefully check the quality and flatness of the board to avoid potential safety hazards caused by the quality of the board. Purchase foam composite board through regular channels and ask the manufacturer for the product fire test report issued by the fire department.

定期檢查泡沫復合板的使用是否有損壞，并對泡沫復合板進行后期維護，避免泡沫復合板面板漆層剝落而影響芯材性能。

Regularly check whether the foam composite board is damaged during use, and carry out post maintenance on the foam composite board to prevent the foam composite board panel paint from peeling off and affecting the core material performance.

由于其特殊的結構，泡沫復合板具有很高的抗壓能力和抗沖擊能力，可以承受各種系統的地面荷載和其他領域。

Due to its special structure, foam composite board has high compressive and impact resistance, and can withstand ground loads of various systems and other fields.

如果保溫板為濟南泡沫復合板，應在涂有粘結膠的一面涂上專用界面劑，待其干燥20分鐘后再使用。泡沫復合板一般應水平鋪設，自下而上，交錯縫寬為板長1/2，必要時適當裁切，尺寸偏差不大于±1.5mm。

If the insulation board is Jinan foam composite board, the side coated with adhesive shall be coated with special interface agent, which shall be used after it is dried for 20 minutes. Generally, the foam composite board shall be laid horizontally from bottom to top, and the staggered seam width shall be 1/2 of the board length. If necessary, it shall be cut appropriately, and the size deviation shall not be greater than ± 1.5mm.

當基墻平整度好時，也可用條貼法，將涂膠的泡沫復合板立即貼在墻上，滑動到位，用2米尺壓平，確保它的平整度和粘貼牢固。

When the flatness of the foundation wall is good, the strip pasting method can also be used to paste the glued foam composite board on the wall immediately, slide it in place, and flatten it with a 2m ruler to ensure its flatness and firm pasting.

板間間隙不應大于2mm，板間高度差不應大于1.5mm。當板間間隙大于2mm時，接縫處應填上絕緣條，板條不得粘膠或使用。接縫處直接用粘合劑填滿，板間高差大于1.5mm的部位應抹平。

The gap between plates shall not be greater than 2mm, and the height difference between plates shall not be greater than 1.5mm. When the gap between plates is greater than 2mm, the joint shall be filled with insulating strip, and the strip shall not be glued or used. The joints shall be directly filled with adhesive, and the parts with height difference between plates greater than 1.5mm shall be troweled.

所有門、窗、孔的拐角處不得有拼接縫，必須用一整塊保溫板切割成型，板縫與拐角的距離不小于200mm。在所有陰陽角的拐角處，必須采用交錯縫合的方法，并按照垂直線用尺子控制偏差，并用90°尺子檢查。

The corners of all doors, windows and holes shall be free of splicing joints, which must be cut and formed with a whole thermal insulation board, and the distance between the board joint and the corner shall not be less than 200mm. At the corners of all internal and external corners, the method of staggered stitching must be adopted, and the deviation must be controlled with a ruler according to the vertical line, and checked with a 90 ° ruler.

要從產品質量上杜絕安全隱患，后期的使用過程中進行維護檢修及時發生隱患！更多相關內容您可以關注網站www.cq4du.com，聯系我們專業的客服人員進行咨詢。

We should eliminate potential safety hazards from product quality, and carry out maintenance and repair in the later use process, so as to avoid potential hazards in time! For more information, you can follow the website www.cq4du.com COM, contact our professional customer service personnel for consultation.